Installation and Removal of the RENEGADE® HOOF BOOTS

Download PDF

Always install hoof boots in a clear area and have somebody assist you in holding your horse.  It is not recommended that you tie your horse during boot installation.  If your horse is not already used to wearing hoof boots, let him spend some time doing so while turned out in an arena or similar enclosure with the boots installed until you are satisfied your horse is non reactive toward wearing them. 

Seek the help of an equine professional if you are unsure about your safety when using, installing or removing hoof boots. 

 

Horse Boot Installation

Renegade Hoof Boot

1. Inspect the boot before use to be sure it’s clean and in good usable condition.

Renegade Hoof Boots Strap

2.  Release the pastern strap and the toe strap.

Renegade Hoof Boots Heel Captivator

3.  Pull the heel captivator down.

Renegade Hoof Boots Installation

4.  Pick up the hoof and insert the hoof into the boot.

Renegade Hoof Boots Alignment

5.  Be sure the boot is centered on the hoof.

Renegade Hoof Boots Fitting

6.  Gently seat the boot onto the hoof with the palm of your hand.

Renegade Hoof Boots Installing

7.  Pull the heel captivator well up onto the heel bulbs.

Renegade Hoof Boots How To

8. Place the hoof onto the ground.

Renegade Hoof Boots

9.  Double-check the heel captivator position.
See the Captivator Positioning page for more detailed information.

Renegade Hoof Boots Strap

10.  Temporarily fasten the toe strap to keep it from lying on the ground.
Then fasten the pastern strap, but make sure this strap has some clearance to the pastern.

THE PASTERN STRAP SHOULD NOT BE TIGHT!

Approximately two fingers’ width of clearance under the strap is recommended.

The pastern strap is NOT the primary means of boot retention; this is the job of the heel captivator.
The pastern strap is a “check strap” to prevent the heel captivator from pulling downward off the heel bulbs in the event of an overreach from a hind hoof , interference with opposing hooves, or when riding through heavy brush, etc.

Renegade Hoof Boots Installed

11.  You should see a gap under the strap as shown above.

Setting the pastern strap tightly will not allow the heel captivator to find its equilibrium with the bulbous shape of the heel bulbs and may force it up against the backside of the pastern bones which could lead to rubbing.

Keep in mind that just as the pasterns descend during weight loading, they also move forward just before the hoof leaves the ground.  If the pastern strap is too tight, then this forward movement of the pastern acts upon the heel captivator, pulling it forward and upward in an undesirable cyclical manner.

Renegade Hoof Boots Pastern Strap

12.  When you are satisfied with the pastern strap adjustment, press the strap together and secure the end by pushing it under the rubber keeper loop.
There are now two o-rings included on the strap.  For additional security, push the strap through both o-rings, then double it back over the closest o-ring and back under the second o-ring.

Renegade Hoof Boots Strap Tension

13.  Return to the toe strap and set the strap tension by pulling the metal cable adapter with one hand and the strap with the other.

By doing this, you can pull evenly from both sides, helping to keep the heel captivator centered on the heel bulbs.

 It is not necessary to tighten the strap tightly.
Just get the strap “snug”. Think about your own shoes, do you like them overly tight?

In dry conditions,  the boots have been tested on a galloping horse with no tension on the straps.  “No Tension” means that all the slack was taken out of the cables by pulling on the strap using only a few ounces of force and no more.

Each user of the boot will need to experiment with tension settings to discover what degree of tension works best for the way your horse moves, the speed you ride and the environmental conditions you ride under.   In all cases, you should always start with loose settings and work your way up from there. If you are having boot retention problems, setting the strap “super tight” is NOT the solution.  Go to the Solutions Page for more info.

Renegade Hoof Boots Secure

14.  When you are satisfied with the toe strap setting, secure the end of the strap by pushing it under the rubber keeper loop.
As with the captivator, the straps now come with two o-rings and can be secured in the same fashion:
Push the strap through both o-rings, then double it back over the closest o-ring and back under the second o-ring.

Renegade Hoof Boots Strap Clearance

15.  After setting the tension on the toe strap, double check the pastern strap clearance and readjust if necessary.

Renegade Hoof Boots Strap Tightness

16. You should see a gap under the strap like this: Approximately two fingers’ width under the pastern strap.

Renegade Hoof Boots Heel Bulb

17. Double-check that the heel captivator is positioned well up onto the heel bulbs.
It is important that the heel captivator is positioned properly so as to conform to the bulbous contours of the heel bulbs, allowing pressure acting upon the heel bulbs to be spread evenly.

Positioning the heel captivator too low can cause excess pressure on the top edge of the captivator and can allow the heel bulbs to pop out of the boot.
Positioning the heel captivator too high can cause the heel captivator to interfere with the pastern bones.

For more detail on heel captivator position, review the Heel Captivator Page.

Renegade Hoof Boots Heel Captivator

18. If needed, lift the hoof back off the ground so you can better check the heel captivator position.

 

Boot Removal

Renegade Hoof Boots Removal

1. Begin by pushing the end of the pastern strap under the rubber keeper loop.

Renegade Hoof Boots Take Off

2. While very important for purposes of installation, to remove the boot it is not necessary to unfasten the toe strap, especially if you follow the recommendations regarding toe strap tension.

Renegade Hoof Boots Uninstall

3. Pick up the hoof and pull the heel captivator downward off the heel bulbs.

Remove Renegade Hoof Boots

4. Use your thumb to push downward on the back of the boot base.

Renegade Hoof Boots

5. And push the boot off from the hoof.

Renegade Hoof Boots Deinstall

6. Be sure to clean the boots well, especially if you encountered muddy conditions during use.

Always inspect the pastern strap and the toe strap for damage or wear.

Dried mud on the sticking surfaces of the straps will reduce their holding power and may cause boot retention problems.
These straps are considered “wear items” and may need to be replaced periodically, but if you keep them clean and free from dried mud they can last the life of the boot.

When finished cleaning, reinsert the pastern strap and store in a dry place out of direct sunlight.